
Zero-water mold removal for attics, crawl spaces and wood framing
Dry Ice Blasting Mold in Lake Worth Beach, Florida
Dry ice blasting mold in Lake Worth Beach, Florida strips mold off wood framing, roof sheathing and block walls without water, sand or chemicals that soak into the structure. Our dry ice mold removal Lake Worth Beach crews handle attic mold, crawl space mold and post-storm water damage mold in homes from Parrot Cove to College Park. We inspect first, contain the work area, then blast, HEPA-vacuum and verify.
What's included
What Our Dry Ice Blasting Mold Service Includes
Every blasting job includes the inspection, containment, blasting, antimicrobial treatment and clearance testing. What varies is the scope, the material being cleaned and whether reconstruction is needed afterward. Here is what you get as standard on a Lake Worth Beach job.
Full Inspection and Written Scope
Thermal imaging, moisture meter readings and a boroscope pass through wall cavities. You get a written scope with photos and a price range before any equipment is unloaded at your door.
Containment and Negative Air
Six-mil plastic sheeting, zip walls, a negative air machine and HEPA filtration. This keeps spores from migrating into the rest of the house while we work, and it is included on every job, not sold as an upgrade.
Dry Ice Blasting and HEPA Vacuuming
Blasting with a second technician running a HEPA vacuum at the nozzle to capture debris as it lifts. We work in sections and check each pass with a light and moisture meter before moving on.
Antimicrobial and Encapsulation
Antimicrobial solution on cleaned surfaces and encapsulation coating on exposed porous framing. We use Fiberlock, Concrobium and Benefect products depending on the surface and who is living in the home.
Post Remediation Clearance Testing
Air samples pulled after containment comes down and sent to an accredited lab. You get the results and the before and after photos in one package you can hand to an insurer or a buyer.
Service overview
What Dry Ice Blasting Mold in Lake Worth Beach, Florida Does
Dry ice blasting mold in Lake Worth Beach, Florida is a media-blasting method that fires soft dry ice pellets at roughly -109 degrees Fahrenheit to lift mold, mildew and surface staining off building materials. The pellets hit the surface, flash-sublimate into carbon dioxide gas, and the thermal shock plus kinetic energy pops the mold loose. Because there is no water, no sand and no soda, nothing is left behind to vacuum out of wall cavities or dry out of insulation. It is the same technology food plants and paper mills use on production lines, adapted here for attics, crawl spaces and wood framing.
Lake Worth Beach sits a few blocks from the Intracoastal, and that salt air keeps relative humidity high most of the year. Add a slow roof leak, a dripping AC condensate line or a storm that pushes water under a door, and black mold infestation shows up in weeks, not months. We run a thermal imaging camera and moisture meter first so we know whether the mold is a surface problem or a wet-structure problem. If it is wet, no blasting method fixes it until the water source is stopped.
The service timeline
Our Dry Ice Blasting Mold Process
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and Mapping
We start with a thermal imaging camera, a moisture meter and a hygrometer to find the wet zones and confirm the mold is not just a surface stain. A boroscope inspection camera goes into wall cavities where we cannot see. This takes 45 to 90 minutes on a typical house, and you get a written scope before any equipment comes in.
Containment Setup
We build a containment barrier with 6-mil plastic sheeting and zip walls, then set a negative air machine with HEPA filters so spores cannot migrate into the rest of the house. Technicians suit up in disposable coveralls and respirator cartridges. Setup runs about an hour for a single room, longer for a full attic or crawl space.
Dry Ice Blasting
The dry ice blasting machine fires pellets at the mold while a second technician runs a HEPA vacuum at the nozzle to capture what lifts off. We work in sections, checking each pass with a light and a moisture meter. A 1,000 sq ft attic typically takes three to five hours of blasting time.
Antimicrobial and Encapsulation
Bare wood that has been cleaned gets an antimicrobial solution, and porous framing that will stay exposed gets an encapsulation coating to seal the grain. We use products from Fiberlock, Concrobium and Benefect depending on the surface and the occupancy. This stage adds two to four hours and is what keeps the mold from returning on the same wood.
Verification and Clearance
We pull the containment, run a final HEPA vacuum pass and take air samples for post remediation mold testing. You get lab results and photos of the before and after. If the numbers are not where they should be, we go back in. Clearance usually lands 24 to 48 hours after the blasting is finished.
Tools & methods
Equipment and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Dry Ice Blasting Machine
Fires dry ice pellets at roughly -109 degrees Fahrenheit to lift mold off wood, block and metal without water or abrasive media. We adjust pressure and pellet feed based on the surface.
Thermal Imaging Camera
Finds temperature differences that point to hidden moisture behind drywall and in ceiling cavities. It is how we locate the leak before we start cutting.
Moisture Meter and Hygrometer
Confirms whether a material is actually wet and tracks drying progress. We log readings before, during and after the job so you have a documented record.
Boroscope Inspection Camera
Slides into wall cavities and behind built-ins to show us the back side of the drywall. It tells us whether blasting will reach the mold or whether material has to come out.
HEPA Vacuum and Air Scrubber
Captures spores and debris at the nozzle and scrubs the air inside containment. We run Abatement Technologies units with HEPA filters on every job.
Negative Air Machine
Keeps containment under negative pressure so air flows in, not out. This is the single piece of equipment that keeps spores out of the rest of your house.
Containment Barrier and Zip Walls
Six-mil plastic sheeting and zip walls isolate the work zone. We seal HVAC registers inside the containment so the system does not pull spores through the house.
Use cases
When to Call for Dry Ice Blasting Mold
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Joists After Supply Line Failure
A rental near Downtown Lake Worth Beach had a supply line let go under the house. Floor joists and subfloor were covered in mold within a week, and the tenant had already moved out over the smell. → We contained the crawl space, blasted the joists and subfloor, treated with antimicrobial and installed a vapor barrier. Total job was three days. The tenant moved back in on day four after clearance passed.
Bathroom Wall Cavity in College Park
A slow shower valve drip had been feeding mold behind the tile for months. Visible mold was limited to a two-foot section, but the boroscope showed growth along the studs behind the whole wall. → We opened one section of drywall, blasted the studs and substrate, and treated the cavity. Only 12 sq ft of drywall came out instead of the full 60 sq ft wall. Clearance passed on the first sample.
Problems we solve
Mold Problems We Solve With Dry Ice Blasting
Most of our calls fall into four buckets: attic mold from roof leaks, crawl space mold from ground moisture, bathroom mold from slow plumbing drips, and post-storm water damage mold. Each one has a different fix, and blasting is not always the right answer. Here is how we sort it out.
Attic mold on roof sheathing after a slow leak
We fix the leak source first, then contain the attic and blast the sheathing and rafters in place. Most attics clean up in three to five hours of blasting time, and we encapsulate the cleaned wood so it does not come back.
Crawl space mold from ground moisture and poor ventilation
We blast the joists and subfloor without adding water to an already damp space, then treat with antimicrobial and address the ventilation. A vapor barrier and a dehumidifier usually go in on the same visit.
Bathroom mold behind tile and painted drywall
We run a boroscope inspection camera into the wall to confirm the extent, then blast the framing and substrate once the leak is fixed. Only the damaged drywall comes out, not the whole wall.
Post-storm water damage mold after flooding
We extract and dry the structure first, then blast the framing once moisture readings are stable. Emergency containment goes up the same night you call so spores do not spread while the structure dries.
Pricing process
What Dry Ice Blasting Mold Costs
$1,800 - $6,500 depending on scope
Square footage affected
Blasting time and dry ice consumption scale directly with the area. A 200 sq ft bathroom ceiling is a half-day job; a 1,500 sq ft attic is two to three days.
Material being cleaned
Roof sheathing and framing blast quickly. Porous block, rough-cut lumber and heavily textured surfaces take longer passes and more pellets per square foot.
Access and containment difficulty
A crawl space with a 24-inch hatch takes longer to contain and ventilate than an attic with a pull-down stair. Tight access adds labor hours to the setup and teardown.
How much does dry ice blasting mold removal cost in Lake Worth Beach Florida?
Most residential jobs run $1,800 to $6,500 in 2026, with attic and crawl space work at the lower end and full-home remediation with reconstruction at the upper end. Dry ice itself runs $2 to $4 per pound and a typical attic burns 150 to 400 pounds, so square footage drives most of the number. We give you a written range after the inspection, before any work starts.
Does dry ice blasting kill mold in Lake Worth Beach?
It removes mold and its food source from the surface, but blasting alone does not sterilize the material. That is why we follow every pass with an antimicrobial solution and an encapsulation coating on porous framing. The combination of physical removal plus antimicrobial treatment is what stops regrowth. Post remediation mold testing confirms the result with lab numbers.
Is dry ice blasting safe for mold in Lake Worth Beach homes?
Yes, when it is done inside containment with proper ventilation. Dry ice sublimates into carbon dioxide, so we monitor CO2 levels in enclosed spaces and keep the area ventilated. Technicians wear respirator cartridges and disposable coveralls. Occupants stay out of the containment zone during blasting, and the space is safe to re-enter once clearance testing passes.
Who does dry ice mold removal near me in Lake Worth Beach FL?
We do, and we cover the whole city plus Hypoluxo Island, Lake Clarke Shores and Lake Osborne Heights. Call (833) 929-5837 and we will schedule an inspection, usually same day if you reach us before noon. You get photos, moisture readings and a written scope before we quote a price.
Ready when you are
Get Dry Ice Blasting Mold in Lake Worth Beach, Florida
Call (833) 929-5837 and we will schedule an inspection, usually the same day. You get photos, moisture readings and a written price range before we start. Licensed, insured and working to the ANSI/IICRC S520 Standard on every job.

Talk with the local team
Request Dry Ice Blasting Mold
Call (833) 929-5837 and you will reach a real person, not a call center. We answer around the clock for emergencies and schedule standard inspections Monday through Friday. If you send photos of the affected area, we can often give you a ballpark price before we arrive.



