Home Mold Inspection

Licensed assessors, moisture mapping, lab-backed answers in 24 hours

Home Mold Inspection in Lake Worth Beach, Florida

A home mold inspection in Lake Worth Beach, Florida tells you exactly where mold is growing, how far it has spread, and what it will take to remove it. We inspect attics, crawl spaces, bathrooms, and HVAC systems with thermal imaging and moisture meters, then hand you a written report with lab results. If you smell something musty or see dark staining after a storm, book a residential mold assessment Lake Worth Beach homeowners trust.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Is Included in Every Inspection

Every home mold inspection in Lake Worth Beach includes the full on-site evaluation, thermal imaging, moisture readings, air and surface sampling, lab analysis, and a written report. Remediation work is quoted separately if the inspection confirms growth. Here is what you get on the day of the visit and in the days after.

01

Full Interior Walkthrough

Attic, crawl space, bathrooms, kitchen, laundry, HVAC closet, and every accessible wall and ceiling. We check for visible growth, water staining, musty odors, and past repair work that might be hiding a problem.

02

Thermal Imaging Scan

A thermal imaging camera reads temperature differences behind drywall, under flooring, and inside ceilings. Cold spots and warm spots both point to moisture. We confirm every anomaly with a pin-type moisture meter before writing it up.

03

Air and Surface Sampling

One outdoor control sample, plus indoor air samples in the affected area and one unaffected room. Visible growth gets a tape-lift or swab sample. All samples are labeled, logged, and shipped to an accredited lab the same day.

04

Lab Analysis and Report

Spore counts by species, moisture percentages, labeled photos, a floor-plan sketch, and a line-item scope of work. Delivered as a PDF within 24 to 48 hours. We walk you through it by phone and answer every question.

05

Moisture Source Identification

Finding mold is only half the job. We trace the moisture back to its source, roof leak, plumbing failure, AC condensate, poor drainage, or high ambient humidity, so the fix addresses the cause and not just the symptom.

Service overview

Home Mold Inspection in Lake Worth Beach, Florida

A home mold inspection in Lake Worth Beach, Florida is a room-by-room evaluation that locates active mold growth, measures the moisture feeding it, and documents the findings in a written report you can act on. We check the attic decking, crawl space joists, bathroom tile and drywall, HVAC air handler, and every spot where a roof leak or slab leak has left water behind. Each inspection follows the ANSI/IICRC S520 standard, so the report holds up with insurers, buyers, and remediation crews.

Lake Worth Beach sits between the Intracoastal and the Atlantic, and that means year-round humidity above 70 percent, afternoon thunderstorms from June through October, and older homes with original cast iron and galvanized plumbing. Those three things combine to feed mold behind walls in the Historic District and under raised floors in Parrot Cove. If you have spotted black mold infestation, smelled musty odors, or had water damage mold after a storm, a home mold testing Lake Worth Beach Florida appointment gives you the facts before the problem spreads.

Lab-Backed AnswersWe pull air samples with a calibrated pump and surface samples from visible growth, then send them to an accredited lab. Results come back in 24 to 48 hours with spore counts by species. That is the difference between guessing and knowing, and it is what a residential mold inspection company Lake Worth Beach clients hire us for.
Hidden Moisture FoundA thermal imaging camera reads temperature differences behind drywall, under tile, and inside ceilings. A pin-type moisture meter confirms the reading. We have found active leaks behind shower walls in College Park that looked perfectly dry from the hallway, and soaked attic sheathing in Tropical Ridge after a single missed roof flashing.
A Report You Can UseYou get photos of every finding, moisture readings in percent, a floor-plan sketch, and lab results in one PDF. Insurance adjusters accept it, real estate agents accept it, and remediation crews bid from it. Sellers use it as a pre-listing disclosure document, buyers use it as a negotiation tool.
Dependable Mold Remediation Service across Lake Worth Beach, Florida
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How Our Inspection Process Works

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Phone Intake

You call (833) 929-5837 and describe what you are seeing or smelling. We ask about recent water events, roof leaks, AC problems, and the age of the home. That call takes 10 minutes and lets us bring the right equipment. Same-day and next-morning slots are usually open.

Stage 1
02

On-Site Walkthrough

A licensed assessor arrives and walks the property with you. We start outside, checking roof penetrations, window flashing, and grading, then move inside to the attic, crawl space, bathrooms, kitchen, laundry, and HVAC closet. Expect 45 to 90 minutes depending on square footage.

Stage 2
03

Moisture Mapping

We run a thermal imaging camera across every wall and ceiling, then confirm hot spots with a moisture meter and a hygrometer. A boroscope inspection camera goes into wall cavities where we cannot see. This is where we find the source, not just the symptom.

Stage 3
04

Air and Surface Sampling

We set an outdoor control sample, then pull indoor air samples in the affected room and one unaffected room. Visible growth gets a tape-lift or swab sample. Everything is labeled, logged, and shipped to an accredited lab the same day.

Stage 4
05

Written Report

Within 24 to 48 hours you receive a PDF with photos, moisture percentages, lab results, and a scope of work. We walk you through it by phone and answer every question. If remediation is needed, we can schedule it or hand the report to your own contractor.

Stage 5

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Thermal Imaging Camera

Reads temperature differences behind drywall, under flooring, and inside ceilings to locate hidden moisture without cutting into the wall.

02

Pin-Type Moisture Meter

Confirms thermal anomalies with actual moisture percentages. Every reading in your report comes from this tool.

03

Hygrometer

Measures relative humidity in each room and in the crawl space. Readings above 60 percent indoors support mold growth.

04

Boroscope Inspection Camera

Slides into wall cavities, behind baseboards, and inside ductwork to see what the eye cannot reach.

05

Air Sampling Pump

Pulls a calibrated volume of air through a spore trap cassette. Sample volume is logged for the lab.

06

DeWalt and Milwaukee Cordless Tools

Used for access cuts and inspection ports when we need to look inside a wall cavity. Battery-powered to avoid tripping breakers.

07

3M Respirator Cartridges and Disposable Coveralls

Standard PPE for any inspection where visible growth is present. Protects the inspector and prevents cross-contamination between rooms.

Use cases

When to Schedule a Mold Inspection

These examples show how the service framework adapts rather than forcing every call through one repair.

Home Mold Inspection
Attic Mold After Roof LeakA homeowner in College Park noticed dark staining on the attic sheathing three weeks after a roof leak. The visible patch was about 4 square feet, but the moisture meter showed elevated readings across 40 square feet of decking and two rafters. → We documented the full extent with photos and moisture readings, and the lab confirmed Cladosporium and Penicillium. The remediation crew removed the affected insulation, HEPA-vacuumed the decking, and treated the rafters with antimicrobial solution. Clearance testing came back at normal spore levels.

Crawl Space Mold in Parrot Cove

A raised home in Parrot Cove had a musty smell in the living room that got worse in summer. The crawl space had no vapor barrier, and joist moisture readings were between 22 and 28 percent. Visible mold covered about 60 square feet of joists and subfloor. → We mapped the moisture, sampled the air in the crawl space and living room, and confirmed elevated spore counts indoors. The remediation crew removed the growth, treated the framing, and installed a 6-mil vapor barrier. Post-remediation air samples came back normal.

Bathroom Mold Behind Tile

A homeowner in Tropical Ridge saw dark grout lines in the guest shower and assumed it was surface mildew. The thermal camera showed a cold band behind the tile, and the moisture meter read 31 percent in the wall cavity. The shower pan had been leaking for months. → We sampled the visible growth and the wall cavity, confirmed Stachybotrys in the cavity sample, and scoped the removal. The remediation crew removed the affected drywall and insulation, treated the framing, and the shower was rebuilt with a new pan and waterproof membrane.

Problems we solve

Mold Problems We Solve in Lake Worth Beach

Most of the calls we get fall into a handful of categories. If any of these sound familiar, an inspection is the fastest way to get a real answer.

ISSUE

Musty smell with no visible mold

We run thermal imaging across every wall and ceiling, then confirm suspicious areas with a moisture meter and boroscope inspection camera. Air samples tell us whether spores are elevated indoors. If the source is in the HVAC, we check the air handler, drain pan, and ductwork.

SYMPTOM

Dark staining on attic sheathing after a roof leak

We inspect the attic decking, rafters, and insulation with a moisture meter and thermal camera. Surface samples confirm the species. If remediation is needed, we scope it by square footage and material type so you know exactly what has to come out.

SIGN

Crawl space mold under a raised home

We check joist moisture, vapor barrier condition, and drainage. Air samples from the crawl space and the living area above show whether spores are migrating upward. The report includes a moisture-source fix, not just a removal scope.

ALERT

Mold after a storm or plumbing leak

We document everything with photos, moisture readings, and lab samples before any work starts. That documentation supports your insurance claim and gives the remediation crew a clear scope. Same-day and next-morning slots are usually available after storms.

Pricing process

What a Mold Inspection Costs

$300 - $650 for most homes; $650 - $1,200 for large properties or multi-area inspections

Phase 01

Square footage

Larger homes take longer to inspect and usually need more air samples. A 3,000-square-foot home may need five or six samples versus three for a 1,500-square-foot home.

Phase 02

Number of samples

Each air sample runs $50 to $75, and surface samples run $40 to $60. More suspect areas mean more samples. We tell you upfront how many we recommend and why.

Phase 03

Crawl space or attic access

Tight crawl spaces and low-pitch attics take longer and may require additional PPE. We add $50 to $100 for difficult access, quoted before the visit.

Questions before we arrive

Frequently Asked Questions

Home Mold Inspection
Call (833) 929-5837
How much does a home mold inspection cost in Lake Worth Beach Florida?

Most inspections run $300 to $650 in 2026, depending on square footage and how many samples we pull. A standard 1,500-square-foot home with three air samples and one surface sample lands around $425. Crawl space or attic-only inspections can be less. You get the exact price on the phone before we schedule.

What does a home mold inspection include in Lake Worth Beach?

A full walkthrough of the attic, crawl space, bathrooms, kitchen, laundry, and HVAC system, thermal imaging of every accessible wall and ceiling, moisture meter readings, and lab analysis of air and surface samples. You receive a written report with photos, moisture percentages, lab results, and a scope of work within 24 to 48 hours.

How long does a residential mold assessment take in Lake Worth Beach FL?

On-site time runs 45 to 90 minutes for most homes under 2,500 square feet. Larger properties or homes with multiple problem areas can take two to three hours. Lab results come back in 24 to 48 hours, so you have a complete report within two days of the visit.

Should I get a home mold inspection before buying in Lake Worth Beach?

Yes, especially on homes built before 1980 or any property that has been vacant through a summer. A standard home inspection does not test for mold. For $300 to $650 you get lab-backed evidence you can use to negotiate repairs or walk away. We regularly inspect homes in the 33460 ZIP for buyers in active contracts.

Ready when you are

Book Your Home Mold Inspection in Lake Worth Beach, Florida

One call gets you a licensed assessor, thermal imaging, lab samples, and a written report in 24 to 48 hours. We have been inspecting Lake Worth Beach homes since 2021. Call (833) 929-5837 and we will find out what is growing, where it is coming from, and what it takes to fix it.

Home Mold Inspection

Talk with the local team

Request Home Mold Inspection

Call (833) 929-5837 and you will reach a real person, not a call center. We answer around the clock for emergencies and schedule standard inspections Monday through Friday. If you send photos of the affected area, we can often give you a ballpark price before we arrive.

102 N Federal Hwy, Lake Worth Beach, FL 33460, USA, Lake Worth Beach, FloridaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now